The European Public Prosecutor's Office (EPPO) announced on 12 November that Italian authorities had seized 454 packages of steel products valued at over €5 million at the port of Naples, following a customs-fraud investigation into two shipments imported in July 2026. The goods originated in Türkiye, were sold to an Italian metalworking company by a Dubai-based exporter, and were declared as zinc-coated steel — a classification the EPPO says would have exempted them from additional duties on certain steel imports into the EU. Physical inspections and laboratory analyses found the products did not match the declaration. The alleged loss to EU and national budgets — additional duties plus related VAT — is put at roughly €3.5 million.

The case is small in tonnage and, so far, unproven: no company or individual has been named, and the EPPO states that all concerned are presumed innocent. Its interest for the wider market is structural rather than criminal. It is an early, concrete illustration of how the EU's post-safeguard steel regime — a 30-category tariff-rate quota with a 50% out-of-quota duty, in force since 1 July 2026 — converts a technical question of tariff classification into a very large sum of money.

The arithmetic that makes classification worth falsifying

Under the previous safeguard, out-of-quota steel faced a 25% duty. The replacement regime, established by Regulation (EU) 2026/1384 after the safeguard expired on 30 June 2026, caps duty-free access at 18.3 million tonnes a year and applies a 50% duty once a supplier's quota is exhausted. The Commission's own factsheet sets out the allocation logic: quota split between FTA and non-FTA partners, country-specific volumes for suppliers holding at least 5% of EU imports in 2022–2024, and a residual pool for the rest. Türkiye is not an EU FTA partner, so its exporters sit in the non-FTA pool and face the full 50% rate on any tonnage above quota.

That is the incentive structure. A misdeclaration that moves a consignment from an over-quota category to an under-quota or exempt one does not shave a margin — it removes half the customs value.

The EPPO does not name the tariff instrument, the CN/TARIC codes or the actual identity of the goods, so the precise mechanism in this case remains an allegation. But the figures are consistent with a duty-driven motive. On the reported numbers, the alleged fiscal loss of ~€3.5 million against goods valued at just over €5 million implies an effective levy of roughly 70% of declared value — higher than a 50% duty alone, which is what you would expect once VAT on the duty-inclusive value is added to the calculation (analysis based on reported aggregates; EPPO has not published the split).

Reported elementFigure
Seized goods valueover €5 million
Packages seized454
Implied average value per package~€11,000 (calculation)
Alleged loss to EU/national budgets~€3.5 million
Implied effective levy on declared value~70% (calculation)
Out-of-quota duty under Reg. (EU) 2026/138450% ad valorem

Why "zinc-coated" is the tell

The choice of declared category is not random. Coated flat products (galvanised sheet and coil) sit in a different product category from uncoated flat products under the TRQ architecture, and different categories have different quota positions, different traditional trade flows and — critically — different residual headroom. Where one category is exhausted and another is not, the classification line is the entire commercial difference.

The trade press has filled in details the prosecutors did not: GMK Center described the goods as "steel coils" and attributed the exemption to safeguard duties; a forwarder blog described "rolled steel products" and said laboratory testing covered one of the two shipments. These are inferences, and at least one is probably wrong on the law — a July 2026 import would fall under the new steel measure, not the expired safeguard. Readers should treat product form (flat vs long, coated vs uncoated) as unconfirmed.

What is confirmed is the investigative method, and that is the more important signal. The case began with an alert from the Naples office of the Customs and Monopolies Agency, proceeded through physical examination and laboratory analysis of the coating, and was executed jointly by the Guardia di Finanza's economic-financial police unit and ADM's Campania anti-fraud office, with searches of homes and company premises and seizure of electronic devices. Laboratory verification of a coating is not a routine border check. It implies targeted risk profiling — and that the authorities are now testing the metallurgical claim, not just the paperwork.

The Dubai layer

The presence of a Dubai-based exporter between a Turkish producer and an Italian buyer is the element most likely to attract attention from compliance teams. It is not illegal, and there are legitimate trading reasons for Gulf intermediaries in steel flows. But in a TRQ system built on origin and, increasingly, on melt-and-pour declarations, an intermediary jurisdiction adds a documentary layer that customs authorities cannot easily verify against production records. The new regulation's melt-and-pour requirement — obliging importers to declare where steel was first melted and poured, with the Commission due to assess by 30 June 2028 whether that origin should govern quota access — exists precisely because conventional origin rules were judged insufficient against circumvention.

This case suggests the next front is not origin fraud but specification fraud: declaring the wrong product, from the right country, into the wrong category. Melt-and-pour rules do nothing to stop that. Only laboratory testing, or much deeper technical scrutiny at the border, does.

What to watch

The visible enforcement signal is one seizure. The deterrent signal is the precedent: a 50% out-of-quota rate raises the prize for misclassification by the same proportion, and the EU has simultaneously increased the number of categories (30) in which a wrong declaration pays. Expect three things to follow. First, more ADM and EPPO actions of this type, particularly at Mediterranean gateways handling Turkish and North African flat products. Second, pressure from EU producers for systematic coating and grade verification, not spot checks. Third, greater scrutiny of traders' declarations by importers themselves — because in this case the Italian buyer appointed the customs representative, which places the declaration liability close to home regardless of where the goods were sold from.

The seizure at Naples is a €5 million case. The classification gap it exposes is worth considerably more than that to anyone willing to exploit it — which is exactly why it will be tested again.

Source & methodology +

MetalMate separates original-source evidence from summary and analysis. Verify the original source before procurement, legal or engineering decisions.

Article status
Published · Version 1
Source date
16 November 2026
MetalMate publication
16 November 2026
Verification
Automated evidence checks; not human reviewed

Italy seizes over €5 million worth of Turkish steel products — SteelOrbis